Informasi dasar.
Penggunaan
Fire Resistant Cable
Disesuaikan
Tidak disesuaikan
Gas Flow Meter
Using Mass Flow Controller
Paket Transportasi
Wooden Case
Deskripsi Produk
Cable And Optical Cable Line Integrity Burning Test Machine
Product Description
It is a test equipment used for cables or optical cables required to maintain the integrity of the line in a separate fire test using a flame (controlled heat output) at a temperature of not less than 750°C. Comply with BS6387, BS8491, IEC60331-2009 and other standards.Technical Parameter
1.Testing station: 1 station, one sample per test. Sample size: length>1200mm.
2.Torch: Banded propane gas torch with venturi mixer and 500 mm nominal nozzle length.
3.Gas flow range: 0 ~ 50L/min(adjustable) Gas flow accuracy:0.1L/min
4.Air flow range: 0 ~ 200L/min(adjustable) Air flow accuracy:5L/min
5.Power supply voltage: AC380V±10%, 50Hz, three-phase five-wire
6.Using gas source: LPG or propane, compressed air
7.Flame temperature: 450° ~ 950°(adjustable)
8.Temperature sensing system: 2 stainless steel K-type thermocouples, temperature resistance of 1100 degrees.
9.Operating power: 3kW
10.Control the test bench by PLC control, touch screen operation, convenient and intuitive.
11.Gas flow meter: using glass flow meter.
12.Short-circuit mode: This equipment changes the previous method of using fuse, and adopts a new type of circuit breaker, which saves the tedious way of replacing the fuse each time.
13.The exhaust system is located on the side of the chassis, which can effectively and quickly exhaust the exhaust gas, which can ensure the oxygen content in the box during the test and make the test results more accurate.
14.Continuous detection device: During the test, the current is passed through all the cores of the cable, and the three single-phase transformers have sufficient capacity to maintain the maximum allowable leakage current at the test voltage. Connect a lamp to each core wire at the other end of the cable, and load a current close to 0.11A at the rated voltage of the cable. When the sample is shorted/opened during the test, all signals are output.
15.The equipment has the following safety protection devices: power supply overload, short circuit protection, control circuit overload protection.Testing station | 1 station, one sample per test |
Sample size | length>1200mm |
Torch | banded propane gas torch with venturi mixer and 500 mm nominal nozzle length |
Gas flow range | 0 ~ 50L/min(adjustable) |
Gas flow accuracy | 0.1L/min |
Air flow range | 0 ~ 200L/min(adjustable) |
Air flow accuracy | 5L/min |
Power supply voltage | AC380V±10%, 50Hz, three-phase five-wire |
Using gas source | LPG or propane, compressed air |
Flame temperature | 450° ~ 950°(adjustable) |
Temperature sensing system | 2 stainless steel K-type thermocouples, temperature resistance of 1100 degrees |
Operating power | 3kW |
Control the test bench by PLC control, touch screen operation, convenient and intuitive |
Gas flow meter | using glass flow meter |
Short-circuit mode | this equipment changes the previous method of using fuse, and adopts a new type of circuit breaker, which saves the tedious way of replacing the fuse each time |
The exhaust system is located on the side of the chassis, which can effectively and quickly exhaust the exhaust gas, which can ensure the oxygen content in the box during the test and make the test results more accurate |
Continuous detection device | during the test, the current is passed through all the cores of the cable, and the three single-phase transformers have sufficient capacity to maintain the maximum allowable leakage current at the test voltage. Connect a lamp to each core wire at the other end of the cable, and load a current close to 0.11A at the rated voltage of the cable. When the sample is shorted/opened during the test, all signals are output |
The equipment has the following safety protection devices: power supply overload, short circuit protection, control circuit overload protection |
Equipment Use Environment
1.The equipment test is carried out in a 3 x 3 x 3(m) combustion chamber (customer-supplied), the chamber has the facility to exclude any gas produced by combustion, and there is sufficient ventilation to maintain the flame during the test.
2.Test environment: the external ambient temperature of the chamber should be maintained between 5ºC and 40ºC.
Mass Flow Controller
The mass flow controller is used for precise measurement and control of the mass flow of gas. Mass flow meters have the features of high accuracy, good repeatability, fast response, soft start, stability and reliability, wide operating pressure range. With international standard connectors, it is easy to operate and use, can be installed in any position, and easy to connect with a computer for automatic control.
Mass flow controller technical parameters:
1.Accuracy: ±2% F.S
2.Linearity:±1% F.S
3.Repeat accuracy:±0.2% F.S
4.Response time:1 ~ 4 sec
5.Pressure resistance: 3 Mpa
6.Working environment:5 ~ 45ºC
7.Input model: 0-+5vAccuracy | ±2% F.S |
Linearity | ±1% F.S |
Repeat accuracy | ±0.2% F.S |
Response time | 1 ~ 4 sec |
Pressure resistance | 3 Mpa |
Working environment | 5 ~ 45ºC |
Input model | 0-+5v |
Shock Vibration, Rain Resistance Test Device (Fire And Water Resistance Test Device)
The performance requirements of the tester, including fire resistance test part (B, cable or fiber optic cable line integrity combustion tester), water spray fire resistance test and mechanical fire resistance test, are applicable to mineral insulated cables with a rated voltage not exceeding 450/750V, under flame conditions for a long time to keep the circuit integrity.
Complies with the fire-resistant cable standard BS6387 "Performance Requirements Specification for Cables to Maintain Circuit Integrity in the Event of Fire".
1.Heat source: a 610 mm long flame-intensive tubular gas burner that can be forced to supply gas.
2.Temperature measurement: a 2mm diameter armoured thermometer is placed near the air inlet, parallel to the burner and 75 mm above.
3.Water spray: a spray head is mounted on the test stand, also in the middle of the burner. The water pressure is 250KPa to 350KPa, spray 0.25L/m2 to 0.30L/m2 of water near the sample. This rate needs to be measured with a tray that has enough depth to allow his long axis parallel to the axis of the cable and placed in the center. This tray is about 100 mm wide and 400 mm long (the device is shown below).Fire And Water Resistance Test Device:Vibration Device:
The vibration device is a low carbon steel rod (25mm in diameter and 600mm in length). The longitudinal section of the rod is parallel to the wall and 200mm above the top of the wall. A shaft divides it into two parts of 200 mm and 400 mm, and the long part faces the wall. Falling from the inclined position to the middle position of the wall from 60°C separated by 30±2s.
Water Spray Test Device And Water Jet Test Device:
1.Water spray: connect the test pipe, make sure there is no problem with the connection, press the water spray to start, manually adjust the water flow regulation "Adjust 2" (this flow is 0-1.4LPM range) on the large panel of the operation cabinet to reach the test demand flow.
2.Water jet: Connect the spray nozzle used for the test, make sure there is no problem with the connection, press the water jet to start, manually adjust the water flow regulation "Adjust 1" (this flow is 2-18LPM range) on the large panel of the operation cabinet to reach the test demand flow.
3.The function of the water release switch button is added to the program: close the water inlet valve and press the water release switch button to drain the remaining water in the pipeline. If the machine does not need to work in winter, it is recommended to remove the pipe connection and press the water release switch to release the remaining water inside the flowmeter to prevent freezing of the instrument. Certifications
Our CompanyHebei Fangyuan Instrument & Equipment Co., Ltd. Was established in 2001. It is a high-tech enterprises which specialized in testing equipments research, produce, sale and service. Our products involved industries about wire and cable, plastic package, fireproof door, paper product package and foods. We have 17 years' designed and developed experience, over 20 aftersales service employees. All of our products comply with international quality standards and are greatly appreciated in a variety of different markets throughout the world.
Alamat:
Building C4 - C5, Fangda Science District, Xingtai, Hebei, China
Jenis Usaha:
Produsen/Pabrik
Jangkauan Bisnis:
Instrumen & Alat Ukur, Kimia, Listrik & Elektronik, Mesin Manufaktur & Pemrosesan
Sertifikasi Sistem Manajemen:
ISO 9001, ISO 9000, OHSAS/ OHSMS 18001
Pengenalan Perusahaan:
Hebei Fangyuan Instrument Equipment Co., Ltd didirikan pada tahun 2007 dan merupakan perusahaan high-tech khusus R&D, produksi, penjualan dan jasa peralatan pengujian. Ada lebih dari 50 karyawan, tim R&D profesional yang terdiri dari dokter dan insinyur, dan teknisi teknik. Kami terutama terlibat dalam pengembangan dan produksi peralatan pengujian untuk bahan kabel dan kabel dan bahan mentah, kemasan plastik, produk pemadam kebakaran dan industri terkait lainnya. Kami memproduksi lebih dari 30, 000 set berbagai peralatan pengujian per tahun, dan produknya dijual di seluruh dunia. Kami memiliki jaringan layanan pemasaran lengkap untuk menyediakan layanan purna-jual dan dukungan teknis jangka panjang yang berkualitas tinggi untuk produk perusahaan.
Hei para departemen ilmu pengetahuan dan Teknologi dalam bulan September 2019, yang merupakan jaminan kuat atas jaminan kualitas dan peningkatan produk-produk perusahaan kita, serta manifestasi kekuatan perusahaan itu sendiri. Selain itu, sistem manajemen kualitas produk dan kekuatan R&D perusahaan juga memberikan pengakuan atas seluruh karyawan, namun yang lebih penting adalah perusahaan kami berharap untuk menjalankan sistem manajemen mutu ISO yang ketat untuk meningkatkan kualitas produk dan layanan perusahaan, dan benar-benar memenangkan kredibilitas dan kepercayaan pelanggan dengan model operasi modular, profesional, terintegrasi, dan modern, serta layanan berkualitas tinggi, serta menjadi landasan yang baik bagi pengembangan jangka panjang perusahaan.
Kebijakan Kualitas: Kepuasan pelanggan adalah standar tertinggi kami, dan menyediakan produk yang sempurna dan layanan yang memuaskan bagi pelanggan adalah usaha kami yang tidak pernah berakhir.
Kebijakan bisnis: Meresapi pertumbuhan pasar, stasiun permanen di baris terdepan ilmu pengetahuan dan teknologi; menciptakan produk baru, pemasaran fleksibel, layanan aktif, pengembangan bersama.
Prinsip kami: "Kualitas pertama, servis lebih dahulu, lebih dahulu dari pelanggan".
Kami berusaha untuk berbuat lebih baik.