Nozzle lilitan koil nozzle Tungsten (W1030-3)

• Kondisi: Baru
• Disesuaikan: Disesuaikan
• Material: Tunsten Carbide
• Aplikasi: Winding Machine
• kekerasan: mencapai kecepatan lebih dari jhr90 derajat
• polandia: gilingan presisi
• Tidak. Model.: W1030-3
• tempat yang bagus: r0.025
• lubang yang berbatu: r0.1
• fungsi: melindungi kabel berenamel
• pasar ekspor: global
• Paket Transportasi: 20PCS/Box
• Merek Dagang: KIM CHEN
• Asal: China
• Kode HS: 8479899960
• Kapasitas Produksi: 50, 000PCS/Month

Deskripsi Produk

Tungsten carbide nozzle for coil winding machine. 
Coil winding wire guide Nozzles(TungstenCarbide nozzle)also call wire guide tubes, wire guide eyelets, wire guide needles, it is used on coil winding machine. It is made precisely of hard alloy and enjoys the hardness up to HRA90. Two terminals andinnerle are all receive mirror surface treatment to ensure enameled wire makes no scrape. High hardness, resistance to flexure, block and impact. 

Coil winding wire guide nozzles(Hard alloy nozzle)Tungste carbide nozzle Features: 
1. High Wear Resistance 
This is assured by the choice of materials for wear elements possessing a minimum hardness in excess of Vickers 1, 000 (HRC 70). 
2. Scratch-Proofing 
Eliminate wire insulation film damage, low friction resistance, stable wire tension. The wire-guiding surfaces are mirror finished by diamond lapping to a surface roughness of 2 -4 micro inches Ra or better, material permit. 

3. Straightness and Stiffness 
Straightness and Stiffness are defined by the wire exit being concentric and inflexible with respect to the nozzle locating? . In plain terms, the wire should exit from the nozzle concentric to the locating? To within 0.02 mm, with or without load. A geometric characteristic presentation is shown at upper left. Concentricity to within 0.01mm. 
4. Precise Exit Radii 
Because the coil winding nozzle's Exit Radii governs the angle of the wire exit from one coil to the next, it should be monitored to + / - 0.025 mm. This is done by digital measurement, shown at upper right.

NO	Model	L	L1	D	D1	d	d1	H
1	W0220-0.8-0602	20	2	0.8	0.6	0.2	0.2
2	W0530-1.5-1007	30	7	1.5	1	0.5	0.5
3	W0530-2-1007	30	7	2	1	0.5	0.5
4	W0535-2-1210	35	10	2	1.2	0.5	0.5
5	W0435-2-1007	35	7	2	1	0.4	0.4
6	W0330-2-0808	30	8	2	0.8	0.3	0.3
8	W0326-2-1007	26	7	2	1	0.3	0.3
9	W0530-2-1010	30	10	2	1	0.5	0.5
11	W835-2.5-2011	35	11	2.5	2	0.8	0.8
12	W0330-2-1006	30	6	2	1	0.3	0.3
13	W0635-2-1215	35	15	2	1.2	0.6	0.6
15	W0530-3-1010	30	10	3	1	0.5	0.5
16	W0630-3-1008	30	8	3	1	0.6	0.6
17	W03303-0807	30	7	3	0.8	0.3	0.3
19	W0630-3-1309	30	9	3	1.3	0.6	0.6
21	W0614-3-1509p	14	9	3	1.5	0.6	0.6	5
22	W1014-3-1509p	14	9	3	1.5	1	1	5
23	W0414-3-1009p	14	9	3	1	0.4	0.4	5
24	W1030-3	30		3		1	1
25	W0326-3-0808	26	8	3	0.8	0.3	0.3
29	W0626-3-1208	26	8	3	1.2	0.6	0.6
30	W1030-3-2014	30	14	3	2	12	12
31	W1230-3-2514	30	14	3	2.5	1.2	1.2
33	W0330-3-0502	30	2	3	0.5	0.3	0.3
34	W0626-3-1208	26	8	3	1.2	0.6	0.6
36	W0330-3-0504	30	4	3	0.5	0.3	0.3
37	W0823-3	25		3		0.8	0.8
38	W0435-1211	35	11	3	1.2	0.4	0.4
39	W03535-3-0811	35	11	3	0.8	0.35	0.35
41	W1025-3-1608	25	8	3	1.6	1	1
42	W0845-3-2017	45	17	3	2	0.8	0.8
43	W1535-3	35		3		1.5	1.5
44	W1036-3-2016	36	16	3	2	1	1
45	W0630-3-1212	30	12	3	1.2	0.6	0.6
46	W0830-4-2015	30	15	4	2	0.8	0.8
47	W1243-4-2515p	43	15	4	2.5	1.2	1.2	20
48	W0843-4-2015p	32	15	4	2	0.8	0.8	20
49	W1232-4.5	43		4.5		1.2	1.2
50	W1543-4-2512p	43	12	4	2.5	1.5	1.5	20
51	W0843-3.9-2019p	20	19	3.9	2	0.8	0.8	19
52	W2020-5	20		5		2	2