Automatic Sintering High Temperature Machine

Article 850 ºC high temperature sintering furnace

Modle :YTH - 25

1. Machine size W1400mm*H1414mm*L6650mm(approx.)

Registration area W1295mm*H910mm*L610mm(approx.)

Heating zone 330mm*10 zone =L5430mm(approx.)

Cooling zone L1175mm(approx.)

Exit area W1295mm*H910mm*L610mm (approx.)

Temperature around the degree of high temperature: 900 ºC MAX use scope: 800 ~ 900 ºC (high) temperature uniformity: 90% of the transmission network bandwidth, empty furnace high temperature constant temperature zone in state holding temperature value of lower, middle and right temperature uniformity is plus or minus 1.5 ºC.

2. Electricity AC380V 3 hoop speed hz 116KW

3. Upper and lower heating system ceramic heating plate

Upper heating plates -10 sets

Lower heating plate -10 sets

4. Conveying system conveying network belt material :N80 with brush cleaning device, conveying mesh specification: W625mm *L14700mm

5. Transmission speed: 100~250mm/min(standard speed :230mm/min)

Transmission motor :AC 3P motor

Frequency converter drive control motor speed, speed setting via RS485 module conversion DC0 ~ 10 v provide Inverter control (makes) control

6. The copper plate-type is attached to and below the cooling chamber, and you can use the copper plate-adsorbed cooling energy to achieve an efficient cooling system.

7. Numerical orimeter is used for flow control

Enterycurtain :15~100L/min*1

Firing air pressure :40~300L/min*1

Cooling of inlet: 15~100L/min*1

Purge/Exit :100L/min*1

8. Control system control mode: dual mode (one is temperature control meter controller and one is industrial control computer display).

10 zone heating zone temperature control, each zone is divided into left, middle and right temperature control meters with 30 zones.

Temperature control mode :P I D(comparison/integral/differential)

Control interface: WINDOWS7

Electrothermal control :SCR

Electric couple :K Type

The rate of increase is limited to 3~5ºC/min during heating

Maximum heating power rate: limiting heating output power rate

Symptoms article states the status graph: in a simple bar chart shows furnace temperature of symptoms, abnormal red, green said.

Setting screen: setting temperature, speed, alarm value, modified value (passcode required)

PID adjustment screen: the display and setting of PID setting value and the heating parameter of PID operation in each temperature region shall be passable code furnace temperature uniformity testing: using high temperature line into the furnace actually, temperature and time and temperature range of all cut graph, to analyze all the zones of warm.
 

8. control system

Control mode: double set type (one set for temperature control meter controller, one for computer display).

10 district heating area temperature control, each district is divided into left, middle, right temperature watch alone control area 30 temperature control table.

Temperature control mode: P I D (ratio / integral / differential)

Control interface: WINDOWS

Electrothermal control: SCR

Electric thermocouple: K Type

Heating limit: when heating is heating, it limits the temperature rise per minute, 3~5 C /min

Maximum heating value: limit heating output power

Bar chart: a simple bar chart shows the state of temperature and temperature. Red indicates normal, and color indicates normal.

SET settings: set the temperature, speed, alarm and correction values.

PID adjust the picture: the PID settings in each temperature zone and the operation of PID heating and display must be coded.

Temperature uniformity test: the high temperature temperature measurement line is actually entered into the dam, and the chart is made with temperature and time and temperature zone to analyze the temperature uniformity of each temperature zone.

Alert mode:

1. warm up and down warnings

2. air pressure upper and lower alarm

3. transmission speed upper and lower alarm

Features:
∗ Reasonable design
∗ High-efficiency
∗ Low consumption, energy saving
∗ Easy to maintain
∗ Easy to operate